CXRacing Engine Swap Kit + Turbo Kit For 2003-2012 Mazda RX-8 With RX-7 FD REW 13B Engine Swap

This Is The Most Complete RX8 13B Swap Kit, Comes with:
Engine Mount Kit + Single Turbo Upgrade Kit + Lower Intake Manifold + Engine Oil Filler Kit

There Are A Few Known Issues with RX8 13B Swap:
1. Stock 13B Twin Turbo Won't Fit.
2. Stock 13B Lower Intake Manifold Won't Fit.
3. Many Swaps Have the Engine Sits Too Low.
4. Engine Oil Filler Won't Fit.

Many People Have to Cut and Hammer the Firewall to Make Things Work. But Our Kit Offers A Simple Solution for the Swap, No Cut, Bolt On Fit.

We Developed This Swap Kit From Scratch, Offers Many New Features and Easy of Installations:
1. Engine Mount Offer Strong Cross Frame Rail Support, Transmission Fits RX8's Stock Transmission Mount.
2. No Need to Hammer or Cut Firewall. Turbo Kit Fits without Cutting Anything.
3. Fits Big Turbo, Up to T76 Compressor Housing and 0.96 AR Exhaust Housing, Supports Big Power.
4. New Lower Intake Manifold Fits, Without Cutting or Hammering Firewall. Comes with New Fuel Rail.
5. 3" Turbo Downpipe Fits Catback Stock Location.
6. Big Front Mount Intercooler and 3" Piping Kit, 50MM BOV.
7. New Engine Oil Filler Tube.

This Is Basically All You Need to Do the 13B/RX8 Swap In Terms of Hardware. The Only Remaining Items to Finish Your Swap Project Are Wiring, Tuning, and Making the Electronic Power Steering Works (These Are NOT Included In This Kit, But There Are Many Solutions for These)

This Kit Is Proven Of Easy Installation, Excellent Fitment, Super Clean Setup.

Note:
1. This Kit Is Developed Based On US Model Left-Hand-Drive. For RHD, We Have Not Tested and Don't Know If There Is Any Fitment Problems(Primary Issue Is Steering Shaft Might Hit Other Parts). We Don't Guarantee Fitment for RHD Chassis.

2. This Item Is for Engine Mount and Turbo Kit ONLY. Intercooler, Piping Kit, Radiator Hard Pipe Kit ARE NOT Included. We Also Offer These Separately, Check Our Other Website Items.



Application:
- Chassis: 2003-2012 Mazda RX8
- Engine: RX-7 FD 13B Turbo

Note: This Is A Single Turbo Kit, Does NOT Fit Stock Twin Turbo

Product Info and Spec:
Engine Mounts:

- Heavy Duty 7 Gauge (0.18") Thick Stainless Steel Panel, with Brace Offers Strong Support
- Adjustable Slotted Bolt Holes
- Polyurethane Bushing Mounts
- Patented Design of Motor Mount is Billet Aluminum, Excellent Strength
- Mounted Across Frame Rails, Offers Excellent Suport

Turbo Kit:
- 11 Gauge Thick Wall Manifold
- T4 Flange, 60mm Vband Wastegate Flange
- T70 Turbo with 0.96 AR Exhaust Housing, Good For 500 HP
- 60mm Vband Wastegate
- 3" Stainless Downpipe, Fits Stock Location Catback
- Turbo Oil Line Kit

CNC Billet Lower Intake Manifold and Fuel Rail:
- CNC Made Fuel Rail, Injector Base, Top and Bottom Flanges.
- Designed with Large Secondary Runners for Extra Airflow Under Extreme Boost and Spool Up
- Has Equal Length Runners, Both Primary and Secondary
- Aluminum Fuel Rail, With AN8 Fitting, Support Large Volume Fuel Flow
- Injectors Are for BOSH Top Feed ONLY
- Injector Dummy Plugs Included for Optional Configuration to run Either 2, 4 or 6 Injectors, For Gasoline, E85, or Methanol Fuel

Engine Oil Filler Tube:
- AN12 Oil Filler Neck, with Cap
- AN10 Breather Port, With Cap

Notes:
- Off Road or Track Use ONLY, NOT for Street Use.
- Due to the Complexity of Swapping a Motor to Different Chassis, Please Make Sure that You Understand the Application Stated Here are the Right Parts for Your Project.
- Parts Being Sold are the Kit Being Advertised ONLY. Other Parts Shown on Pictures are for Demo Only (of Our Complete Swap Kit). Check Our Other Website Item.
 


Highlights:
- Especially Designed, Made for the Application Stated
- Fully Tested, Simple Easy Installation
- Offers Excellent Performance Gains

Items_Included:
- Engine Mount Kit
- Turbo Manifold with WG Dump Tube
- T70 Turbo with Oil Line Kit, Air Intake Pipe and Filter
- 60mm Vband Wastegate 12 PSI
- 3" Stainless Downpipe (2 pcs set)
- Aluminum Lower Intake Manifold with Fuel Rail
- Engine Oil Filler Tube
Note: Intercooler, Piping Kit, Radiator Hard Pipe Kit ARE NOT Included.

Engine Mount Installed Pictures:

Note: With Our Mount Kit, Oil Pan Sits Approximate 3/4 Inch Lower than the Lower Point Of the Front Cross Support

Intercooler Kit Installed Pictures:

Turbo Manifold and Downpipe Installed Pictures:

Lower Intake Manifold Installed Pictures:

Engine Oil Filler Tube Installed Pictures:

     

Write a review

Please login or register to review

13B Turbo Engine Mount Manifold Downpipe Intake MF Kit For RX8 RX-8 Swap RX7 FD

  • Brand: CXRacing
  • Product Code: TRB-KIT-13B-RX8-ESK-NO-IC
  • Availability: In Stock
  • $2,510.72


Available Options


  • Emissions Control Warning:
  • It is illegal to sell, install, or offer for sale any aftermarket part that alters or modifies the original design or performance of the motor vehicle pollution control system. Product(s) listed here is(are) solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for use on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).

  • All Products by CXRACING are solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for used on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).

  • PROPOSITION 65 WARNING

  • These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.